WALL-MOUNTED TROUGH 1.5 M, GALVANIZED

Feeder made entirely of stainless steel, with large rounded corners: animal-friendly construction with no protruding edges or corners. ¾" rigid male water connection incorporated, no flexible connection line required Connection from the right or left side is possible by relocating the valve. MASTERFLOW float valve installed, water flow up to 40 l/min (11 gallons/min), ¾" front male connection The rounded float valve cover can be turned upwards without tools! Water-saving flat drinker, less sludge: water savings per tilting flat drinker of up to 25,000 l (6,600 US gallons) per year (considering a cleaning interval of 2 days), compared to normal tilting drinkers with a water content of 200 l (6,600 US gallons) Free and easy access to the water surface and optimal drinking height. Galvanized wall and floor fixings Volume: 1.5 m: 55 l Options for frost protection Heating element under the trough Easy fixation under the trough. No sharp edges when cleaning the trough. Provides frost protection of the trough up to approx. 20 °C. To guarantee a freezing-free piping of the trough, the heating element can be installed in the trough. -20 °C. To ensure a frost-free feed pipe, a 24 V, 20 W, 2 m (Order No. 101.0861) or 24 V, 30 W, 3 m (Order No. 101.1863) anti-freeze heating cable must be used. A SUEVIA transformer (24 V) is required for the power supply. A thermostat (order no. 101.0389) can be additionally installed for automatic switching on and off of the transformer. The heating cable should be wrapped around the pipe and connected to the heating element of the sprue in parallel to the power supply cable coming from the transformer. If this heating cable is installed in plastic pipes, make sure that this water pipe is suitable for both hot and cold water. For better heat distribution, the water pipe should first be wrapped with aluminum adhesive tape (Order No. 101.1099). Suitable heating elements for troughs: 130.8522, 130.8532 = 1.5 m: 131.6061 (24 V, 180 W) 130.8523, 130.8533 = 2.0 m: 131.6062 (24 V, 360 W) Heating in the trough Heating element 24 V, 180 W Model 6063 (order no. 131.6063), with stainless steel cover and cable connection box included. Guarantees frost protection of the trough down to -20°C. For installation, only four holes need to be drilled in the bottom of the channel as per drawing. Increased frost protection of the valve. For extremely cold areas, a valve heater (24 V, 7 W, 131.0527) is recommended for increased frost protection. Connection to a water circuit When connected to a water circuit and in combination with a SUEVIA heating unit, frost protection for both the water line and the trough water is achieved. ¾" stainless steel circuit pipe (Ref. 131.0591) suitable for installation in SUEVIA flat tilting troughs with MASTERFLOW float valve. 1" stainless steel circuit pipe, which runs through the entire trough. Ideal for connection to a water circuit in large barns. Which 1" circuit pipe fits which trough? 130.8521, 130.8531 = 1 m: 1" circuit pipe cannot be used. 130.8522, 130.8532 = 1.5 m: 131.6122 Frost protection SUEVIA frost protection grid with connecting pieces (order no. 131.0592). For retrofitting to SUEVIA tilting troughs. Frost protection without electricity! In case of frost risk, the installed and adjusted anti-freeze grid opens automatically and the adjusted amount of water flows into the trough through the float valve below the anti-freeze grid: the water in the trough remains in motion and is prevented from freezing. Excess water produced by the anti-freeze grid is properly channeled through the drain kit, which is mounted in front of the float valve on the back side of the trough. Type of valve Float valve Valve material brass Thread size ¾" Suitable for circuit Yes Bowl material stainless steel Max. pressure 5 bar / 72.5 psi (high pressure) Heated Yes (electric) Recommended for dairy cows